Whole House Repipe in Pflugerville, TX

When should you call about whole house repipe?

• Two or more slab leaks
• Discolored water
• Low pressure at several fixtures

Related guide: how providers choose a repair path.

What should you do right now?

1. Shut off the main water valve. It is in the meter box near the street, or where the main line enters your garage or an outside wall. Turn it clockwise until it stops.
2. Warm floor? Close the cold-water inlet on top of the water heater.
3. Water near outlets? Stay away. Switch off the breaker only if you are on dry ground.
4. Smell gas? Leave and call your gas utility or 911 from outside.

What will the local provider do?

1. Map every fixture
2. Run new supply lines
3. Switch the house over to the new lines
4. Test every fixture

Start with our Pflugerville slab leak guide if you are not sure what you need.

What causes the problems whole house repipe finds?

A whole house repipe replaces every supply line. It is considered when problems are spread through the system, not in one spot.

• Original copper or galvanized pipe throughout
• Multiple slab leaks over a few years
• Corrosion causing discolored water
• Low pressure at many fixtures

Which warning signs matter most?

What should you expect?

A repipe is usually done room by room. Water is off for part of each day while lines are switched over, then the whole system is pressure-tested at the end.

When is this the right choice?

A repipe is a bigger job than a single repair, so it helps to plan. Ask the provider which rooms will be worked on each day, where wall openings will be made, and how long water will be off. Clearing space under sinks and around the water heater before the start date can save time.

How can you prevent it?

• Track how many leaks your home has had
• Ask for a pipe condition check during any repair
• Plan a repipe before a major remodel
• Consider PEX for flexibility with soil movement

What is a whole house repipe?

A whole house repipe replaces all the water supply lines in the home, not just one leaking section. The old pipes, whether under the slab or in the walls, are taken out of service and new lines are run to every fixture. Most repipes in slab homes run the new lines through the attic and walls so the slab stays closed.

Repiping is a larger project than a spot repair, but it resets the plumbing to new, and it ends the cycle of repeat leaks from aging pipe.

When should you consider a repipe?

How does a repipe work?

1. The provider inspects the home and plans the new layout.
2. Furniture near work areas is covered or moved.
3. Small openings are cut in walls and ceilings to run new lines.
4. New pipe is run from the main supply to each fixture.
5. Each fixture is connected, and the old lines are capped.
6. The system is pressure-tested and flushed.
7. Drywall openings are patched.

Many providers restore water to the home each evening so you can stay in the house during the work. Ask about the schedule before you book.

PEX or copper?

How should you prepare?

• Clear space along walls with plumbing fixtures
• Plan for short water outages during the day
• Move valuables and fragile items out of work areas
• Ask whether pets and children should be out during the work
• Get the scope, schedule and price in writing
• Ask who handles drywall patching and painting

What does a repipe change for daily life?

Once the work is done, most homeowners notice steady water pressure and no more worry about new slab leaks on the supply side. Since the new lines run through walls and the attic, any future service is easier to reach. Each fixture usually gets its own shut-off valve, which makes small repairs simpler.

A repipe also helps when selling the home. Buyers and inspectors often ask about pipe age and past leaks. Keep the invoice, permit and any warranty in your home records.

How does a repipe compare with repeated spot repairs?

Each spot repair means another detection visit, another opening, and another round of flooring or drywall work. After two or three leaks on aging pipe, the total cost and disruption can come close to a repipe, without ending the risk of the next leak. A provider can review your leak history and pipe condition and lay out both paths so you can compare them.

What affects the cost of a repipe?

• Size of the home and number of bathrooms
• Number of fixtures and appliances connected
• One-story or two-story layout
• Pipe material chosen
• Drywall patching, texture and paint
• Permit and inspection fees

Ask for a written quote that lists what is and is not included, and how long the provider expects the work to take.

What happens to the old pipes?

In slab homes, the old supply lines under the foundation are usually capped and left in place. Pipes in walls may be removed where they are easy to reach, or capped and abandoned. Either way, they no longer carry water, so they cannot leak. Ask the provider where each old line will be capped.

Where in Pflugerville can you get whole house repipe?

• Slab leak detection in Blackhawk 78660
• Slab leak detection in Windermere 78660
• Slab leak detection in Falcon Pointe 78660
• Slab leak detection in Villages of Hidden Lake 78660
• Slab leak detection in Highland Park 78660
• Slab leak detection in Heatherwilde 78660
• Slab leak detection in Avalon 78660
• Slab leak detection in Sorento 78660
• Slab leak detection in Carmel 78660
• Slab leak detection in Springbrook 78660
• Slab leak detection in Commons at Rowe Lane 78660
• Slab leak detection in Northtown Park 78660
• Slab leak detection in Brookfield 78660
• Slab leak detection in Cambridge Heights 78664
• Slab leak detection in Park at Wellspoint 78664
• Slab leak detection in Verona 78660
• Slab leak detection in Bohls Place 78660

Related services

• Slab Leak Repair
• Pipe Rerouting
• Tunneling Under Slab
• Direct Access Repair
• Epoxy Pipe Lining

Whole House Repipe questions